things_to_buy
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
things_to_buy [2024/04/01 13:36] al |
things_to_buy [2024/10/05 05:06] (current) meantux |
||
|---|---|---|---|
| Line 15: | Line 15: | ||
| | F684ZZ Mini Ball Bearings Double Shielded Flanged Ball Bearings for 3D Printer Model 4x9x4mm | 1 | Amazon - B07CKLBBXX | | | F684ZZ Mini Ball Bearings Double Shielded Flanged Ball Bearings for 3D Printer Model 4x9x4mm | 1 | Amazon - B07CKLBBXX | | ||
| | 4mm to 5mm Brass Shaft Coupling Joint Connector | 1 | Amazon - B0C1RD6KFY | | | 4mm to 5mm Brass Shaft Coupling Joint Connector | 1 | Amazon - B0C1RD6KFY | | ||
| - | | Nema17, 12v, 1.8 degrees/step, stepper motor | 1 | Bi Polar – 4-Wire. Must have a D-Cut in shaft! | | + | | Nema17, 12v, 1.8 degrees/step, stepper motor (42X42X34) | 1 | Bi Polar – 4-Wire. Must have a D-Cut in shaft! | |
| - | | LED ENG NW 3LEDS 4200K | 16 | Digikey 1647-1030-1-ND | | + | | LED ENG NW 3LEDS 4200K | 6 | Digikey 1647-1030-1-ND | |
| | Sensor Optical 15mm Module | 2 | Digikey Z3028-ND | | | Sensor Optical 15mm Module | 2 | Digikey Z3028-ND | | ||
| | Connector HSG 3 Pos 2.50mm | 2 | Digikey A112637-ND | | | Connector HSG 3 Pos 2.50mm | 2 | Digikey A112637-ND | | ||
| Line 37: | Line 37: | ||
| ^ ITEM ^ QTY ^ NOTES ^ | ^ ITEM ^ QTY ^ NOTES ^ | ||
| | 608ZZ Ball Bearings | 4 | | | | 608ZZ Ball Bearings | 4 | | | ||
| - | | Rod – 8mm (0.315 inch) diameter, 15cm length (6 inches) | 11 |Rod should be strong and smooth (Polished Stainless Steel for example). Amazon B07XP4H2K5 | | + | | Rod – 8mm (0.315 inch) diameter, 15cm length (6 inches) | 2 |Rod should be strong and smooth (Polished Stainless Steel for example). Amazon B07XP4H2K5 | |
| | #6 x 3/4” nuts and bolts. | 4 | Hardware Store | | | #6 x 3/4” nuts and bolts. | 4 | Hardware Store | | ||
| | #6 x 1/2” nuts and bolts. | 6 | Hardware Store | | | #6 x 1/2” nuts and bolts. | 6 | Hardware Store | | ||
| - | | Nema17, 12v, 1.8 degrees/step, stepper motor | 2 | Bi Polar – 4-Wire. Must have a D-Cut in shaft! | | + | | Nema17, 12v, 1.8 degrees/step, stepper motor (42X42X34) | 2 | Bi Polar – 4-Wire. Must have a D-Cut in shaft! | |
| | Pre-Crimped Wires | 8 | Digikey 455-3241-ND (Get extras “in case”) | | | Pre-Crimped Wires | 8 | Digikey 455-3241-ND (Get extras “in case”) | | ||
| | Housings Receptacle White 0.098" (2.50mm) | 2 | Digikey 455-2267-ND | | | Housings Receptacle White 0.098" (2.50mm) | 2 | Digikey 455-2267-ND | | ||
| | Small Wire Ties | Many | For holding wires together. | | | Small Wire Ties | Many | For holding wires together. | | ||
| + | |||
| + | ===== Remaining Purchased Parts Required: ===== | ||
| + | |||
| + | ^ ITEM ^ QTY ^ NOTES ^ | ||
| + | | 2’ x 2’ x ½” (70cm X 70cm x 13mm) Wooden Board | 1 | Everything will be attached to it. | | ||
| + | | 10” x 10” (25cm x 25 cm) Steel Plate | 1 | We found a galvanized steel “Sign” at a craft store. | | ||
| + | | Hot Glue Gun w/Glue | 1 | Get a decent one that doesn’t drip. | | ||
| + | | Double Sided Carpet Tape | 20” | Used to hold down metal plate but hot glue would work as well. | | ||
| + | | Main Base Assembly (from above) | 1 | | | ||
| + | | Turntable w/Shoe (from above) | 2 | | | ||
| + | | PC Power Supply (AT or ATX) | 1 | Must have a connector to power the Gugusse PCB | | ||
| + | | Gugusse 3.1 PCB (assembled) | 1 | | | ||
| + | | Raspberry Pi 4B (4GB or more) w/SD 16GB+ | 1 | | | ||
| + | | Raspberry Pi HQ Camera with Lens, Extended Cable, and Adapters. | 1 | Many Lens options here. Suggest Edmunds Optics 17.5mm FL f/5.6, Blue Series M12 Lens - #83-943 / C-Mount to M12 Adapter for UCi Lens - #12-879 – 2X 5mm C-Mount Extension (eBay) | | ||
| + | | Configured EX-DN10 Hole Sensor | 1 | Found at Ali Express - Needs additional parts - See PCB documentation | | ||
| + | | M2.5 x 16mm Bolt | 2 | To Mount Camera | | ||
| + | | M2.5 Nut | 2 | To Mount Camera | | ||
| + | | #6 X 3” Bolt | 1 | | | ||
| + | | #6 Nut | 1 | | | ||
| + | | Neodymium Magnets | 8 | Ours are 2.2 x 1.5cm – Anything around that size will work. | | ||
| ---- | ---- | ||
things_to_buy.1711992977.txt.gz · Last modified: 2024/04/01 13:36 by al
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
